Education

BENINCA BRAIN 24 PDF

Beninca Brain 24 Manual. Instruction Manual for Beninca Brain 24 Control Panel. Copy to Email · Send to Mobile. Print. Download · Buy Product. Name. 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8k2 Command central for 1/2 24Vdc motor, for single or sliding doors: BRAINY Beninca Brain 24 – EasyGates Manuals & Guides. L Rev. 02/06/02 CENTRALE DI COMANDO CONTROL UNIT STEUEREINHEIT CENTRALE DE.

Author: Fenrishakar Mebei
Country: Mauritania
Language: English (Spanish)
Genre: Sex
Published (Last): 14 September 2010
Pages: 438
PDF File Size: 5.26 Mb
ePub File Size: 19.44 Mb
ISBN: 313-3-25085-483-3
Downloads: 41289
Price: Free* [*Free Regsitration Required]
Uploader: Shakajas

OFF mloc Selects the type of electric lock used. Comments to this Manuals Your Name. Regulates the delay time of motor 2 on opening with respect to motor 1 Mot. The speed of the motor during braking is determined by the SLDS parameter value.

Braain of braking With braking enabled SLD logic: By pressing ‘print’ button you will print only current page. The operating time is adjusted at normal speed during motor 1 opening and closing phases. For example, with the leaves completely closed the display is as follows: After the activation of closure limit switches the control unit delays the stop by approx. The step-by-step impulse or transmitter impulse has no effect during the opening phase. RTR Completely erase the receiver memory. One segment of the display is linked to each input.

  DANLOD NARMAFZAR PDF

To use this benjnca, close the limit switch contacts with jumpers. At the end of the set time the control unit orders a closing manoeuvre. If the code is not valid or is not in memory, the wording Err is displayed. With 2ch logic Off: Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software release. Before each opening manoeuvre the power supply is interrupted for the time set by the parameter TLOC.

Radio receiver enabled only for rolling-code transmitters. OFF Blc Vrain lock function is enabled or disabled. OFF serL Service light function is enabled or disabled on output The operating time is adjusted at normal speed during motor 2 opening and closing phases. The transmitter codes are not erased from the receiver. Page of 9 Go. If the battery charger board CB. The amperometric sensor activation is interpreted by the control unit as obstacle present in the gate movement area.

An incorrect setting of these parameters may result in an hazard. For the light control use the auxiliary relay. Page 6 only by the triggering of the limit switch or by the amperometric sensor.

  IVAN CANKAR CRTICE IZ MOJE MLADOSTI PDF

OFF Sld Enables or disables slowing. If the code is not valid, the wording Err is displayed. The performance of the output is preset by 2ch parameter, see previous parameter. It’s a community-based project which helps to repair anything.

SCA contact, open gate indicator.

Beninca Brain 24V PCB Board and Casing

Similarly to the safety edge activation, the control signal is sent to stop and reverse movement for approx. Electric lock with latch, normally not fed.

To print the manual completely, please, download it. The preset time should therefore be lower than the real stroke of the operator. Parameters, Logic and Special Functions The tables below describe the individual functions available in the control unit.

Beninca BRAINY24 24Vdc Control panel for 1 or 2 motors REPLACES BRAIN24

Control Unit Beninca CP. Rbain the code is valid, it is erase and OK appears. For example, with a 20s stroke, preset 17s to start the braking phase, 3s in advance with respect to end of movement.

Make sure the devices are correctly connected i.